General

What Not To Do With Power Coating Oven

Whether you’re an experienced powder coater or you’ve just started coating, you know that your powder coating oven is an expensive appliance and an important part of the entire coating operation. Keeping your coating oven in good condition is critical to long-term success. A well-maintained powder coating oven can last over a decade, produce thousands of high-quality parts for your customers, and be a considerable source of income for your business – if taken care of properly.

To help you avoid making a costly – and potentially dangerous – mistake, here are five tips of what not to do with your powder coating oven.

1. Don’t run the batch oven above the recommended temperature

While most powder coating ovens are built to sustain operation at temperatures of up to 450º F, there are some models that can withstand up to 500º F or higher. It’s important to determine the type of powder coating oven that you own and the appropriate temperature settings it can handle. Significantly jumping up in temperature in an attempt to save curing time can harm your equipment, possibly trip the safety devices, and ultimately damage the finish on your parts.

Every powder has a specific temperature range. Going above that range will make the finish of your part brittle, less durable, and can cause discoloration issues – especially with glossy white finishes. The extra minutes you might save aren’t worth voiding your batch oven warranty or damaging expensive components.

2. Don’t reduce the exhaust airflow in an attempt to save on heating costs

All professional-grade, gas-fueled ovens are built to exhaust a certain amount of air when the oven is being used. The exhaust causes the air to move in a particular pattern throughout the oven cabin, maintaining a stable temperature. If you reduce or eliminate the exhaust airflow within the oven, you can create hot and cold spots. These temperature changes will cause the powder to either overbake or underbake, which can result in poor part finishes and lots of reworks to be done.

This can also cause problems with safety devices. Disabling the safeties to prevent them from tripping violates important safety codes that can void your warranty.

3. Don’t overload your batch oven trying to increase throughput

If you are putting too many parts and racks into it, there’s a high chance that you will accidentally block the oven exhaust or airflow ducts inside the cabin. If blocked, stress is added to the exhaust fan and can shorten the service life of both the fan and the drive motor. Blocking the exhaust can also promote hot spots inside the oven that can damage the parts, racks, or even the oven itself. If the supply ducts from the heater are obstructed, the coating powder can be blown off of the parts.

It’s an even bigger problem if the airflow through the heat unit gets reduced. Not only will it kill fuel efficiency, but it will also cause the temperature inside the heat unit to increase significantly. This can result in the heat unit’s fan failing, reduced motor service life, erratic operation due to safety circuits being tripped, and even structural damage to the heat unit itself.

Also Read: What to Know Before Opening A Virtual Restaurant

4. Don’t skip oven maintenance

No matter how busy your coating line is, skipping scheduled maintenance for your powder coating oven will shorten the service life of crucial oven components and eventually lead to critical failures. Routine maintenance procedures include keeping your oven clean, servicing the burner regularly, lubricating bearings as directed, checking the ductwork for obstructions, and not letting minor issues be put off for too long before fixing them.

5. Don’t install the oven too close to other equipment

Installing your oven too close to other equipment for the sake of “saving shop space” can violate safety regulations and allow debris, fumes, or even powder from other appliances to cause problems with your oven or your finishes.

Routine maintenance and scheduled service can keep you in operations for years to come. At Reliant Finishing Systems, we pride ourselves on providing some of the best and most efficient batch coating equipment on the market. By following these tips, making sure you’re following a set maintenance schedule, and contacting us for service visits when an issue arises, you can help increase the lifespan of your equipment and maximize your ROI.

Check out: Kitchen Gadget Write For Us

Review What Not To Do With Power Coating Oven. Cancel reply

kamran sharief

Share
Published by
kamran sharief

Recent Posts

Is Artificial Intelligence transforming the World of Digital Marketing?

Nowadays, practically every industry uses artificial intelligence thanks to the field's development. Businesses are creating… Read More

July 3, 2022

jio rockers telugu movies 2021 crack Download Tamilrockers, Filmyzilla, 123MKV, 123Movies

jio rockers telugu movies 2021 crack Site to Download jio rockers telugu movies 2021 crack… Read More

July 3, 2022

Vega Movies Download 300mb FHD Bollywood, Hollywood Movies, Web Series In 420p, 720p, 1080p Quality

Vega Movies: The Vegamovies website offers movies in every quality format, including 240P, 360P, 720P,… Read More

July 2, 2022

Movierulz Torrent Magnet Download 2022: Is It Safe And Legal To Download Movies?

movierulz torrent magnet websites. Many people enjoy watching movies. Com leaks movies without charge. The… Read More

July 1, 2022

How CPG Companies Measure Promotion Effectiveness to Get Trade Promotions Right

Stimulating demand for saleable items across all channels doesn't come cheap, and CPG companies spend… Read More

June 23, 2022

Is Energy A Good Career Path?

The short answer is yes. A world without energy is an impossible thought due to… Read More

June 15, 2022